It’s been a few days since my last post.  I actually worked on a few little odds and ends since the last post but nothing significant as I was waiting for my calipers to arrive so I could check the thickness of the strips I was trying to bend.  It turned out that my previous attempts had been on strips that were 3mm to 4mm thick rather than the 1mm to 1.25mm that I expect to be bending for the real violin ribs.  So, I planed one of the strips down a bit, to about 1.75mm and gave it another go.  The bending went much more smoothly!

I made a couple of other changes in my bending process also.  On the advice of many, from the internet, I heated my bending iron hot enough so that water didn’t just boil when it hit the iron but rather it beaded up and danced off the iron.  But, you don’t want the iron so hot that it scorches the wood so make sure and let the iron heat up for a good bit of time and test on a scrap piece of wood for scorching.

The other significant, though simple, change I made was to use a piece of parchment paper between my aluminum bending strap and the wood strip I’m bending.  This is done to protect the wood from being stained when it rubs against the aluminum.

As you can see in the picture and in the video, the results were good.  When I was done, I thought the fit was probably close to good enough to glue.  However, I discovered the next morning that either the curve had changed or the board had shrunk and it no longer fit tightly at both ends.  Next time, when I get done bending the strip, I’m going to try clamping it into the c-bout on the form over night to see if that helps.

One thing I learned along the way was to NOT try to use carpet tape to hold the strips down while planing.  I had read this recommendation on several forums but it didn’t work out well at all for me!  When I got the strips down to a little over 1.5mm thick, I found that the adhesive on the tape was just too strong and the strips would break as I tried to remove them from the tape.  Maybe there’s some brand that isn’t as permanent, but the standard double sided cloth carpet tape that I tried was a disaster… fortunately only on scrap wood!

Here’s today’s video.  Enjoy!

Print PDF

Today was all about learning how to bend wood.  I need to pretty much know what I’m doing before I start trying to bend the real violin rib wood because there’s basically jut enough to do the violin without much room for mistakes or scrap.

So, I started the day by ripping off a few 20 inch thin strips of spruce from the long 2×4 I had to buy the other day.  These strips will also serve as stock for the rib linings that I’ll be cutting next week.  I had cut several different thicknesses of the strips and started out trying to bend the thickest of the bunch… why?  I have no idea, but it turned out to be a mistake.  Later, after many failed attempts, I cut a piece much closer to the thickness of the ribs.  I had some success when combining this thinner piece with a modified approach to the bending process.

The real breakthrough came when I got some advice from amateur luthiers  Kathy and Ray (THANK YOU!!!) who suggested:

1. Use a cut down piece of aluminum flashing as a bending strap.
2. Don’t wet the wood too much.

I also read in “The Art of Violin Making” that you should use a damp rag just to get some steam into the wood but that the actual bending should be done with wood against iron.

In the end, after about 6 hours and many intermediate failures, Success!  I managed to make a very tight bend without a single split or tare.

Here’s the video showing the whole process I went through today.  The right way is shown near the end.

FYI, I might consider buying one of the stainless steel straps sold by luthier tool shops to avoid the possible blemishes caused by the aluminum rubbing off on the wood.

Print PDF

Well, it is the 5th day since I started but I really didn’t do anything on the violin other than square up one edge on the form.  I did get the wood in though, as well as a few other things that I’ll need.

I spent a little time going over some of the things I’ve had to get for the project so far and covered them in this video.  You also get to be tortured by me struggling with some exercises on the E-String.

On the violin itself, I’m at a stand still for a couple days.  The next step is to get the rib stock down to about 1mm thick.  To do that, I’ll need a set of calipers which have been ordered and are due in on Monday.  In the mean time I’m going to practice bending wood and make some tools I’ll be needing.

Print PDF

Today’s task was to cut to shape the corner and top and bottom blocks.  The first step was to plane the blocks to be flush with the violin building form.  Next, I transferred the pattern onto the blocks.  Once I’d neatened up the pattern using a french curve, I did the cutting on a band saw.  The last step, not seen in the video, was about two hours of sanding and checking to make sure that all the block edges were square with the bottom of the form.

If I ever do this again, I think I’ll try to keep the band saw a bit further from the cut line.  I’ll use small diameter sanding wheels on the drill press to get down to the final shape and by doing so, keep everything square as I go.

Here’s a video showing most of what I did.  Oh, and my apologies… I did not practice violin today so no tortuous background music

Print PDF

Today’s task should have been simple.  It should not have involved a trip to the lumber yard and another to the hardware store.  However, it turned out not to be simple and did indeed involve a trip the the lumber yard and another to the hardware store.  On the upside though, I ended up getting a really awesome back cutting saw and several clamps that were on sale.

Today was all about getting the form cut out and the corner and end blocks put in place… mission accomplished.  Check the video:

The trip to the lumber yard was required because it turned out that I didn’t have a piece of wood suitable for the corner blocks or end pieces.  So, for the lack of about 8 inches of wood I had to go buy a 16ft spruce 2×4.  Oh well, the “scrap will come in handy I’m sure!  At the lumber yard they cut the board in half for me using a very nice back cutting saw.  When I commented about it I was told that they sold them inside the office… They did indeed sell them, in fact, the sold one to me

The trip to the hardware store was required because the clamps I had were either an inch too short or 4ft too long.  As it turned out, they were having a “Hot Deal” on the clamps I needed and have been wanting for a while anyway.  So, it all turned out for the best (with the possible exception of my wallet).

Cutting out the form went well.  The only thing that I’d give more thought to on a 2nd go around would be how to cut the slots for the corner blocks.  Cutting the slots with a 1/8 inch band saw made it impossible to achieve parallel, straight, or perpendicular cuts.  This along with difficulty cutting the blocks themselves using a table saw and miter saw took a lot more time than expected.  If I had it to do over again (Stradivarius part deux?) I might think about changing blades on the band saw and cutting the blocks and “entry” slots on the form with a much wider blade.

So, anyway, while it did take about twice as much time as expected (what doesn’t other than hot water in the microwave?) it’s done for the day.  Tomorrow, after the glue is dried, I’ll trim down the corner and end blocks, mark the pattern and cut out the last of the form.

Enjoy!

joe

Print PDF

This route makes a loop through a lot of wide open ranch land in North Eastern Stanislaus County and takes you along the Stanislaus River between  the town of Knights Ferry, and Kerr Park.

Start at Junction of Milton and Sonora Roads

Parking on Sonora Rd

While we could start this loop from anywhere along its course, and one could make a good argument for starting and ending in the community of Knights Ferry, we’re going to start at the junction of Milton Rd and Sonora Road (‘A’ on the map).  We get there by turning South off of Highway four onto Milton Road and driving about three and a half miles.  There’s a wide gravel shoulder on Sonora Road at the junction big enough for a few cars to park.

We’re going to do the loop clockwise for no particular reason.  I’ve seen people do it counterclockwise also.  So, we are going to head straight down Sonora Road.  This first leg is the easiest to follow as we’re going to just stay on Sonora Road for almost the next 12 miles until we go through the town of Knights Ferry to the Stanislaus Recreation Area / Picnic area just outside of town.

Cattle Country On Sonora Road

Most of Sonora Road goes through cattle country with wide expansive views, and in the spring time lush green low rolling hills for as far as you can see.  You won’t have to look hard for the cattle, they’re everywhere along this stretch of road.  If you keep your eyes open though you might catch a family or two of groundhogs along the way.  In the first 8 miles, we climb about 140 feet to just under 300 feet in elevation.  We then drop down by about 60 feet in the next third of a mile and bounce back up 123 feet in less than three quarters of a mile.  Now into the course a little over 9 miles, we are at the highest point we’ll see today at about 358 feet in elevation.  After reaching this peak (loosely defined), we descend about 120 feet in a little over a mile.  Now, just under ten and a third miles into the course, we reach the junction of Sonora Road and Orange Blossom Road.  If you wanted to shorten the loop by a few miles you could turn right on Orange Blossom Road, but then you would also miss out on seeing the quaint community of Knghts Ferry which we’ll be coming to shortly

Welcome To Knights Ferry

At the junction with Orange Blossom, we turned left at the stop sign to stay on Sonora Road and regain about 60 feet over the next two thirds of a mile.  At just under 11 miles into the the course, we begin our descent into the Stanislaus river basin and the community of Knights Ferry.  This descent is only about 128 feet over a half mile.

If you don’t care to stop or slow down on your ride, you could just turn right at Cemetery Street (‘C’ on the map), just before you come into “down town” Knights Ferry (also loosely defined).  However, it’s worth taking the short ride through town and maybe taking a short break at the Knights Ferry Stanislaus River Recreation Area just on the other side of town (‘B’ on the map).   There are porta-potties, and a picnic area at the recreation area and according to a sign we saw there, they apparently also have drinking water though I did not take the time to scout it out.

We’ve come just under twelve miles when we reach the Recreation Area just outside Knights Ferry.  By turning around and heading back the way we came, we could cut the total distance down by about 14 miles, to about 24 miles.  However, we’re going to continue on the loop.

Steep but Short

From the recreation area, we retrace our route back about a half mile, through town, to Cemetery Road (‘C’ on the map) and turn left up the short steep hill.  On Cemetery, we gain about 140 feet in under a third of a mile.  We’re going to turn at the first left onto Frymire Road (‘D’ on the map).  However, you might want to take a short detour continuing on the now flat Cemetery road keeping your eyes open to the left.  You just might spot the Camel or Zeedonk (Zeebra + Donkey = odd) or some other exotic creature that call this ranch home.  This also gives you a little break before we climb a little more on Frymire.

If you wanted, you could just continue a bit more on Cemetery road and then turn left on Morrision.  We’re going to turn from Cemetary onto Frymier though and after a short assent and a gradual decent, we’ll catch up with Morrison after about 1.7 miles.

At the junction of Frymire and Morrison (‘E’ on the map), we’ve now come about 14.4 miles from the start.  We’re going to go left on Morrison, heading due West for a while before it turns North just before the intersection with Orange Blossom Road.  We’re only on Morrison on a shallow descent for just over eight tenths of a mile.  Since getting on Frymire, we’ve been following the course of the Stanislaus River pretty closely and will continue to do so for several miles to come.  There are several river access recreation areas along the way similar to the one outside Knights Ferry.

At the junction of Frymire and Orange Blossom Road (‘F’ on the map) we turn left and continue to follow the course of the Stanislaus river for about nine tenths of a mile before turning right, up Horseshoe Road (‘G’ on the map).  We could skip this little detour and continue on Orange Blossom, but the extra couple miles helps get us a bit closer to 4o miles total (actually 38.2).  So, we take the easy 2.4 mile “horseshoe” and find ourselves back to Orange Blossom road (‘H’ on the map) where we’ll turn right and continue once more to follow the course of the Stanislaus River.  At this junction, we’ve come just over 18.5 miles from the beginning.

Orange Blossom Recreation Area

Back on Orange Blossom now, we continue 2.5 miles until we come to Rodden Road.  We continue to follow the Stanislaus by turning Right on Rodden Road (‘I’ on the map).  Just off to our left we’ll see the rather large and inviting “Orange Blossom Recreation Area”, yet another river access park.

We continue on Rodden Road, staying along the northern bank of the Stanislaus River for a little over 2.9 miles.  At this point, almost 24 miles into our journey, Rodden takes an uphill turn toward the North, and away from the river bed.  After another half mile, Rodden Road turns back generally Westward.  We continue on Rodden Road for about 1.4 miles where it ends at a T-junction with Twenty Eight Mile Road (‘J’ on the map).  We’re now about 28.8 miles from the beginning.

We’re going to turn right on Twenty Eight Mile Road which starts out heading us due North.  A little over 2.8 miles on Twenty Eight Mile Road, we come to the cross street, Dorsey Road, and the beginning of the Woodward Reservoir Stanislaus County Park which will be on our left as we cross over Dorsey.  We continue on Twenty Eight Mile Road which soon begins to take turns to the East, North East, North, West, etc, as it skirts the boundary of the Reservoir.

About three miles from crossing over Dorsey, we come to a junction with Eastman Road (‘K’ on the map).  From here, Twenty Eight Mile Road continues on straight, to the North, and would get us back to the beginning more quickly, but it also turns into a dirt road here.  So we’re going to take Easman Road West, to the left.

Eastman Road, like Twenty Eight Mile Road, skirts the reservoir park boundary, but on the Northern edge.  We follow Eastman generally Westward for about 2.2 miles where it ends at a T-junction with Twenty Six Mile Road (‘L’ on the map).  We’ve now come a little over thirty three and a third miles from the start.  We take Twenty Six Mile Road, right, to the North.  About 2 miles after we join Twenty Six Mile Road, the road name changes (though there is no sign that I saw) to East Sonora Road (‘M’ on the map).  From here, the road turns toward the East and in another 1.9 miles, takes us back to the junction of Sonora Road and Milton Road where we started (‘A’ on the map).

I have yet to personally ride this route on my bicycle, but other than the short steep climb up Cemetery road, the climbs seemed relatively gentle.  The traffic was light to non-existent for most of the route with the exception of “down town” Knights Ferry and the stretch of Twenty Six Mile Road and East Sonora Road, but even those  did not seem too dicey.

If you’ve ridden the route, or if you catch any mistakes I’ve made in this description, please feel free to leave your comments!

joe

Print PDF

Just a short update on the status of things… Since you’re reading this it means you’ve found us at our new location.  Make sure and update your bookmarks / rss links etc to our new address.

joe

Print PDF

The trail to Bull Run Lake can be difficult depending on what kind of shape you’re in and how much water is flowing in the streams you have to cross, but the lake is beautiful and a great place to camp.

From the Stanislaus Meadow parking area just off of Highway 4, it’s almost exactly 4 miles to the lake.  You can cut up to a half mile off of that if you drive in on the dirt road to the official trail head.  However, there are some pretty rutted sections of that dirt road that I would not want to take without elevated ground clearance and maybe four wheel drive.

Stanislaus Meadow Trail Head

I parked in the large parking area, about four miles East of Lake Alpine on the South side of Highway 4, and walked the dirt road into the official Stanislaus Meadow Trail Head.  The parking area is at about 7900 feet elevation.  It was a pleasant walk and I wanted to get some video footage anyway.  From the parking area I followed the road for about 0.55 miles to the well signed Stanislaus Meadow Trail Head.

There are no facilities at the parking lot or trail head so plan ahead.  Make sure and bring plenty of water for the hike.

Near the trail head is a junction with the Emigrant Trail that will take you to Mosquito Lakes in one direction and to Lake Alpine in the other.  On some topo maps the trail to Lake Alpine is shown, but the trail to Mosquito Lakes is not.  There is another trail junction further up toward Bull Run Lake that also goes to Mosquito Lakes and some people make a loop out of it.

From the Stanislaus Meadow Trail Head, we travel mostly South down a gentle slope for a little more than a half mile to the signed boundary of the Carson Iceberg Wilderness Area.  Remember that motorized vehicles and bicycles are not allowed in the Wilderness Area.

Continuing mostly South from the Wilderness Area Boundary, or path begins to steepen it’s descent.  This steeper South bound part of the trail continues for a little over six tenths of a mile until we reach a crossing near the headwaters of the North Fork of the Stanislaus River, about 1.7 miles from the parking area.  When I did this hike in early September the river was dry.  However, earlier in the season when the snow is still melting, this crossing can be challenging.  There are several places where people or horses have chosen to cross depending on the rate of flow.  This is the low point of our hike at about 7440 feet.

From the crossing of the North Fork of the Stanislaus River, we begin to climb gently in a Southeasterly direction for about four tenths of a mile where we come to another stream crossing.  Again, when I did the hike this stream bed was also dry but it would not have been just a few short weeks earlier.

From the stream crossing at about 2.1 miles from the parking area, we turn toward the North East, and begin to climb more steeply.  In another six tenths of a mile, or about 2.7 miles from the beginning, we come to the trail junction I mentioned at the beginning of this article.  If we continue North East at this point we can go to Heizer Lake or further on to Mosquito Lakes and Highway 4.  Today though we are going to Bull Run Lake so we take the right fork of the trail which now takes us toward the South East.

For about then next four tenths of a mile our path is nearly level… it won’t stay that way.  At about 3.1 miles from the beginning we start one of the steepest inclines of the hike.  Going steeply up hill we travel first to the South East, then East, then South for a bit less than half a mile where we come to a short level stretch and a small pond on our right.  I know my first reaction upon reaching this pond was great disappointment having mistakenly concluded that this was my destination… luckily the person I was hiking with knew better.

From the pond it’s only another four tenths of a mile (all up hill) until we reach Bull Run Lake at about 8360 feet elevation.  The lake is fairly large and has quite a few great camping spots pretty much all around its perimeter. Being a relatively short hike and a beautiful location, it is a very popular spot for weekend day hikers and back packers.

The hike into Bull Run Lake is easier that the hike to Wheeler Lake.  They both have lots of good camping spots.  One big difference between the two is that the scenery going to Wheeler Lake is very volcanic in nature whereas the hike into Bull Run Lake is like a lot of the Sierras… Granite, Granite, Granite.  In fact, there are some stretches of the trail where you pretty much have to rely on the rock ducks (small cairns) and tree blazes (examples shown in the video) along with map and compass and GPS if you’re lucky.

I hiked this trail on one of the busiest weekends of the year, Labor Day weekend.  I saw lots of people on the trail, some who looked like they were prepared, others who did not.  There are some steep sections, exposed sections, gravely sections, and depending on the time of year, some significant stream crossings.  Bring plenty of water, good hiking shoes, and stay within your abilities.

Elevation Profile

I hope you get the chance to enjoy this hike to Bull Run Lake!

Print PDF

Wheeler Lake Trail Elevation Profile (one way)

This trail takes us up to the top of what some folks call Wheeler Ridge and then down to Wheeler lake from the Woodchuck Basin Trailhead off of California State Route 4.  In the late summer at these elevations the snow is just melting off and wildflowers are bursting from the ground almost everywhere.

Before we get started with the trail description, let me throw a little caution your way.  While this trail is not too long, it is almost all up hill or down hill, sometimes steeply, often on exposed slopes, at elevation.  Know your physical abilities and stay within them.  Also, be aware of Sierra mountain weather.  It can go from clear skies to thunder and lightening very quickly!

Woodchuck Basin Trailhead Sign on Hwy 4

We start our trek at the Woodchuck Basin Trailhead parking area which is located about 1.2 miles North-East of the North-East end of Lake Alpine on California State Route 4.  This dirt parking area is fairly large but this is also a very popular trail for day hikers, equestrians, and backpackers so on busy holiday weekends it can get a bit crowded.  If you have 4 wheel drive, you can actually drive further up the dirt road leading to the actual trailhead and perhaps find a spot.  On the weekend we hiked the trial, parking was abundant.

Remember that this trail goes into the Mokelumne Wilderness area so only foot or horse traffic is allowed.  No bicycles and no motorized vehicles.

Woodchuck Basin Trailhead

From the trailhead parking area, we follow the narrow dirt road a little less than a quarter mile, generally North, to the trailhead sign.  This path takes us up a gentle slope under tree cover.  You may notice multiple fire rings along the way.  When large equestrian groups come up, you’ll often find these rustic campsites occupied.

From the trailhead sign we continue up hill with a slightly increased slope.  We go about a half mile in a North North-east direction for about a half mile to the easy crossing of intermittent Silver Creek.

This section of the trail is wooded and we begin to get a taste of the wildflowers that await us on the other side of the ridge.  Click on the thumbnails for larger images…

click to enlarge

click to enlarge

click to enlarge

click to enlarge

Silver Creek Crossing

Crossing Silver Creek was a simple step-over for us.  We’ve come a little less than 3/4 of a mile so far and the approach to Silver Creek has been a pleasant, shallow, grade with lots of wildflowers to encourage us forward.

The trail immediately following the creek crossing takes us through a beautiful meadow as we approach the wall of volcanic rock that forms the rim of Woodchuck Basin.

This is a good opportunity to take a break, take some pictures, and get well hydrated because soon we’ll be making our way up the basin wall toward the ridge line.

click to enlarge

click to enlarge

click to enlarge

click to enlarge

Wilderness Area Sign

Less than two tenths of a mile from Silver Creek, or about 0.87 miles from the beginning, we come to the well marked beginning of the Mokelumne Wilderness area.  Up to this point we have been heading mostly North, making our way up the slope of Woodchuck Basin  toward a domineering volcanic wall.  After the sign for the wilderness area, we turn toward the West and begin the steady trudge traversing the basin wall, making our way steadily up hill, now at somewhat less gentle slope.

Up to this point, the trail has led us through a mostly wooded landscape.  That is about to change.  As soon as the trail turns to the west, and begins the climb up the slope of the basin wall, we notice that the cover becomes more sparse, and the track drier and more gravel strewn as we go.  For about the next two tenths of a mile, as we continue to climb we are still treated to plenty of mountain wildflower eye candy but it gets thinner and thinner as we go.  Also along this stretch we begin to be able to look down into the valley to the South and see Lake Alpine  as well as  Utica and Union reservoirs.

click to enlarge

click to enlarge

click to enlarge

click to enlarge

Exposed Climb Up Basin Wall

Finally, at just a little over a mile from the beginning of our hike, and a couple tenths of a mile since we turned toward the west in the Wilderness Area, we find ourselves on the completely exposed, mostly South facing slope above Woodchuck basin.  From here up to the ridge top there is virtually no cover and the trail goes pretty continuously up hill.

We have already gained almost 630 feet in elevation to about 8382 feet.  Over the next nine tenths of a mile we’ll gain another 377 feet where we’ll reach the ridge overlooking the valley where our destination lies.

View From the Trail

To compensate for the exposed conditions on this stretch of the trail we are granted wide open vistas of the Dadanells and beyond.

From the point where the exposed section starts, it’s about eight tenths of a mile until we first reach the.  At this point, we look down into Underwood Valley to the North-West, and Mount Reba almost directly to the West.

At this point there are spur trails off to the East and West that follow the ridge line.  However  we’ll follow the main trail which now turns to the North East and up for another tenth of a mile or so.

Last Up Hill Stretch

This last uphill section is now on the North West facing slope of the ridge and the conditions are dramatically different than they were on the other side.  Here, instead of a bare, sun beaten slope, we’ll often times find the trail blocked by snow all the way into late summer.  We also pick up some tree cover for a brief time.

View From The Top

At the end of our almost continuous up hill journey, we’ve come about 1.98 miles and gained over 1000 feet in elevation to 8758 feet.  We are met here by spectacular view down into Avalanche Meadow below, and the mountains in the distance.

If the late summer snow hasn’t already turned you back, this is a good place to stop for awhile, assess your strength, stamina, and water supply.  The trail section that comes next is even steeper than the one we’ve just come up and the first part of it is again on an exposed slope.  Add to that that the first part of the remaining trail is down steep switchbacks on loose scree making footing unsure.

That said, if you’re up to the task, what awaits you down in Avalanche Meadow and Wheeler lake may make it worth the effort.  Just make sure you know you can hike out once you have committed by hiking down this slope.

Looking Back Up Switchbacks

So, from the top of the ridge we continue down a rocky set of switchbacks for the next 500 or so feet, quickly losing about 130 feet in elevation.  Keep your eyes open because there are several “false” trails where people have either accidentally or on purpose cut off some of the switchbacks creating much steeper and more difficult alternatives.

At the bottom of the switchbacks we continue North East in a more direct fashion, now entering the wooded forest floor.  Our elevation loss (gain coming back!!) continues to be fairly steep but the footing is better than it was on the switchbacks.

Unnamed Intermittent Stream

We continue North East from the switchbacks for a little less then two tenths of a mile where the trail turns to the South East, toward the inside of a bowl formed of volcanic rock, and Avalanche Meadow.  Just a bit further on, now 2.32 miles from where we started we come to our second intermittent stream crossing.

From this intermittent stream we continue South East for about 3 tenths of a mile still making our way down the North East facing wall of the gigantic bowl.  At that point, about 2.6 miles from our beginning, the trail turns North East.

As we get deeper into the bowl, it’s obvious that there is much more water and the conditions are much less harsh than on the ridge line.

click to enlarge

click to enlarge

click to enlarge

click to enlarge

Continuing now to the North East for less than 2 tenths of a mile, we come into the stunning Avalanche Meadow and our closest approach to the babbling creek that flows out of it to feed Wheeler Lake.  Fed by melting snow around the bowl that surrounds the meadow, the wildflowers here were amazingly prolific and were growing almost head high.

Avalanche Meadow

At this point, about 2.78 miles from where we started, we’ve dropped back down over 600 feet from the ridge top.  The area in the immediate vicinity of the meadow has a shallower slope than that leading up to it or that which lies ahead.  It’s really an awesome place to take another break, take a bunch of pictures, and get hydrated.

From Avalanche Meadow we turn toward the North West and travel down an increasingly steep slope for about 1/3 of a mile to the Wheeler Lake basin.  In just a few hundred more feet, we come to a trail marker indicating that we are at the junction of the Sandy Meadow trail to the right and Frog Lake trail to the left.  Straight ahead is our destination, Wheeler Lake.

Wheeler Lake South Shore

Wheeler Lake is a very attractive lake for camping because it has quite a few good camping spots near the lake but under forest cover.  We started down the trail toward Frog Lake, around the South end of the lake.  Just a little ways off the trail under nearby trees to the West, we saw several inviting camp sites.  We also saw plenty of evidence that this area is sometimes frequented by range cattle which I suppose could dampen the camping experience.

At the point where the Frog Lake trail begins to move further from Wheeler Lake, we made our way, easily, cross country toward the North shore of the lake.  We stopped at a point that looked like a nice campsite and had lunch.

Wheeler Lake North Shore

From the North shore you can look back and see the volcanic bowl that feeds Avalanche Meadow and Wheeler Lake.

Well, we’ve come almost three and a half miles now, and the mile coming down from the ridge line into the Wheeler Lake basin was fairly steep coming down.  But, as usual…. it was much steeper going back up!  Unless you are in tip-top condition, and completely acclimated to the elevation, coming back up to the ridge from Wheeler is definitely a place where you want to pace yourself and take lots of breaks.

Once you make it to the ridge then, as they say, “it’s all downhill from here”.  Also, since most of the trail coming back down from the ridge is not as steep as on the other side I found that I was able to maintain a good pace all the way back to the parking area.

I hope you’ve enjoyed this trail description and the pictures I’ve shared here.  I also hope that someday you get to enjoy some or all of the trail as much as I did.  Just know your limitations and don’t get yourself stuck in a situation you can’t get out of.

I’d love to hear your comments!

joe

Print PDF